Step Tutorial for Installing a Bathtub
Step Tutorial for Installing a Bathtub
Blog Article
Are you currently in search of help around Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't specifically brain surgery, however it does require solid plumbing, carpentry, and often, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably difficult project. If the old bathtub is conveniently available, the task can move immediately; if you have to open up a wall surface to remove the old bathtub and place the brand-new bath tub, the job is much harder. In either situation, the job is within a home handyman's abilities, although you will certainly need a helper to move out the old tub and also embeded in the brand-new one. Make sure you have certified yourself for the task and also are comfortable attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is much better to think about employing one before you start. Chances are you might need a professional plumber to make tube connections.
This short article will certainly aid you install a new tub in your washroom if you have actually currently acquired a new bathtub as well as do not require to transform the setup of your previous water pipelines.
Your tools and also product list should comprise the following:
Preparing for the Setup
First of all, the supporting frame supplied with the bath needs to be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to make sure that if the tap includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps system to avoid pressure on the tub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to now prepare to be suited its final placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be rather troublesome due to the restricted gain access to that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the remaining water that will come from the pipelines. Once the supply pipelines have been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old sealing compound.
Before carrying on to fit the new taps, compare the pipeline connections on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, place the bathtub in the called for position. The wood boards are practical in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by checking the spirit level and adjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit all-time low of the outermost adaptable faucet connector to the suitable supply pipe by making a compression sign up with; then do the very same for the various other faucet.
Activate the supply of water and also inspect all joints and also new pipework for leaks and tighten them if essential. Fill the bath tub and likewise inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, deal with the bath paneling as described in the supplier's instruction manual. Tiling and securing around the bathtub should wait until the tub has actually been made use of at the very least when as this will resolve it into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin making certain that the washers are in place between the faucet and also the sink. Secure the tap in place with the manufacturer provided backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal tap ports. The former type must be attached to the tap finishes first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a rigid seal, triggering the water to pass through the wall surface between the bath and the tiling, bring about issues with wetness as well as possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes as well as cartridges, and also are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealant can break fairly very early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly readily available on the market. It is suggested to fit the floor tiles using water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm just very curious about How to Install a Bathtub and I am praying you enjoyed the new blog entry. Appreciated our write-up? Please share it. Help somebody else check it out. Many thanks for your time. Please check up our website back soon.
Dial, we're waiting! Report this page